Embedded Jetdirect submenu
To gain access to this menu, touch CONFIGURE DEVICE, and then touch EMBEDDED
JETDIRECT.
58
Chapter 2 Using the control panel
ENWW
Item
Options
Values
Explanation
TCP/IP
ENABLE
ON
OFF
ON: (default) Enable the TCP/IP
protocol.
OFF: Disable the TCP/IP protocol.
HOST NAME
An alphanumeric string, up to 32
characters, that is used to identify the
device. This name is listed on the
Jetdirect configuration page. The
default host name is NPIxxxxxx,
where xxxxxx is the last six digits of
the LAN hardware (MAC) address.
CONFIG
METHOD
BOOTP
DHCP
AUTO IP
MANUAL
Select BOOTP (Bootstrap Protocol)
for automatic configuration from a
BootP server.
Select DHCP (Dynamic Host
Configuration Protocol) for automatic
configuration from a DHCP server.
Select AUTO IP for automatic link-
local IP addressing. An address in the
form 169.254.x.x will be automatically
assigned.
Use the MANUAL settings menu to
configure TCP/IP parameters.
MANUAL
IP ADDRESS
SUBNET MASK
SYSLOG
SERVER
DEFAULT
GATEWAY
IDLE TIMEOUT
IP ADDRESS: The unique IP address
of the MFP.
SUBNET MASK: The subnet mask for
the MFP.
SYSLOG SERVER: The IP address of
the syslog server used to receive and
log syslog messages.
DEFAULT GATEWAY: The IP
address of the gateway or router used
for communications with other
networks.
IDLE TIMEOUT: The time period, in
seconds, after which an idle TCP print
data connection is closed. (The
default is 270 seconds).
ENWW
Configure device menu
59
Item
Options
Values
Explanation
TCP/IP
DEFAULT IP
AUTO IP
LEGACY
AUTO IP: A link-local IP address
169.254.x.x will be set.
LEGACY: The address 192.0.0.192
will be set, consistent with older
Jetdirect products.
PRIMARY DNS
Specify the IP address (n.n.n.n) of the
Primary Domain Name System (DNS)
Server.
SECONDARY
DNS
Specify the IP address (n.n.n.n) of the
Secondary Domain Name System
(DNS) Server.
PROXY SERVER
Specifies the proxy server to be used
by embedded software in your MFP. A
proxy server is typically used by
network clients for Internet access. It
caches Web pages, and provides a
degree of Internet security, for those
clients.
To specify a proxy server, enter its IP
address or fully-qualified domain
name. The name can be up to 64
characters.
For some networks, you might need to
contact your Independent Service
Provider (ISP) for the proxy server
address.
PROXY PORT
Enter the port number used by the
proxy server for client support. The
port number identifies the port
reserved for proxy activity on your
network, and can be a value from 0 to
65535.
IPX/SPX
ENABLE
ON
OFF
ON: Enable the IPX/SPX protocol.
OFF: Disable the IPX/SPX protocol.
FRAME TYPE
AUTO
EN_8023EN_IIEN
_8022EN_SNAP
Select the frame-type setting for your
network.
AUTO: (default) Automatically sets
and limits the frame type to the first
one detected.
EN_8023EN_IIEN_8022EN_SNAP:
Frame type selections for Ethernet
networks.
APPLETALK
ENABLE
ON
OFF
Enable or disable the AppleTalk
protocol.
DLC/LLC
ENABLE
ON
OFF
Enable or disable the DLC/LLC
protocol.
60
Chapter 2 Using the control panel
ENWW
Item
Options
Values
Explanation
LINK SPEED
AUTO
10T HALF
10T FULL
100TX HALF
100TX FULL
The print server will automatically
configure itself to match the network
link speed and communication mode.
If this process fails, 100TX HALF is set.
10T HALF: 10 Mbps, half-duplex
operation.
10T FULL: 10 Mbps, full-duplex
operation.
100TX HALF: 100 Mbps, half-duplex
operation.
100TX FULL: 100 Mbps, full-duplex
operation.